| |
Used Stuff :
We have a few used parts that
have accumulated over the years from servicing MerCruiser sterndrives. All of the
parts came out of boats that were in a running condition. Questionable
gears and shafts were sent out for Magnetic Particle Inspection and therefore
sold "as is" with no warranty or returns.
Click here for shipping
costs.
After clicking above, change the weight of the item
and change the shipping zip code to match yours.
Our zip code is 48316
Propshaft Straightening Fixture - Used
With this fixture you can straighten most Pre-Alpha, Alpha One
and Generation II propshafts to within .002 total indicator reading measuring it
at the end of the splines as shown.
$400.00
Shipping
Wt. 40 Lbs.
|
Used Individual Lower Unit Gears
These are
used lower unit gears. They came out of Pre-Alpha and Alpha One lower
units which were used from 1965 - 1991. We had all of our used lower gears
sent out
for magnetic particle inspection.
The ones which passed are now being sold individually as
is.
$65.00 Per
Gear
|
Used 1965 - 1975 Gimbal Housing Assembly.
 This
is a used gimbal housing, gimbal ring and bell housing which was used from
approximately 1965 - 1975. This gimbal housing has the
large snap ring holding in the gimbal bearing.
We are mainly selling this for the gimbal ring and steering lever which is
very tight. The gimbal housing and bell housing has some corrosion on the
bottom of the mounting flange where the u-joint bellows clamps onto. It
comes with all 3 bellows and gimbal bearing.
$250.00 Shipping
Wt. about 30 Lbs.
|
New - Sierra Power Steering Oil Cooler
 We
have discontinued this item. It is a new Sierra power steering oil cooler
# 18-2587 ( MerC # 99356A2 ) It measures 7 3/4 long, has a 1 1/4 OD at
each end for cooling water and (2) 3/8 hose barbs for the power steering
fluid.
$85.00 Shipping
Wt. 3 Lbs.
|
|
Mitutoyo Dial Bore Gage Set # 511-106
 This
is a used Mitutoyo bore gage set which is in very good condition. It will
measure bores from 2" to 6" diameter within .0001 accuracy.
$150.00 Shipping
Wt. 3 1/2 Lbs.
|
1970 - 1991 Upper Housings
These are used MerCruiser empty upper housings which were used from approx.
1970 to 1991. They will fit Pre-Alpha & Alpha One Bell housings and
lower units.
$190.00 Shipping
20 Lbs.
|
1970 - 1982 Pre-Alpha Lower Housings
These are used MerCruiser empty lower housings which were used from approx.
1970 to 1982. They will fit Pre-Alpha & Alpha One upper housings.
$200.00 Shipping
20 Lbs.
|
|
5 Gallon Pail Pump & Oil
 This
is a used 5 gallon pail pump. It comes with a plastic pail which has
about 7 " ( about 2 1/2 gallons ) of Sierra High Performance (
synthetic ) gear oil in it.
This item
is being sold for a local pickup only. Sorry, no shipping.
$100.00
|
Alignment Tools For Twin Engines
 We
took an 1 1/8 combination wrench, cut & welded a long handle on it for
locking down the front engine alignment bolts on twin V-8 engines. The
short end of the wrench is used to adjust the up & down.
$40.00 Shipping
Wt. 6 1/2 Lbs.
|
1968
- 1983 Pre-Alpha Lower Gear Set & Vertical Shaft
 This
is a used lower gear set. It came out of a perfect running drive. It comes
with the vertical shaft, forward gear, pinion gear, reverse gear and
pinion bearing.
$200.00
|
Michigan
Wheel - Reconditioned 19 Pitch Prop
 This
is a reconditioned Michigan Wheel ( p/n # 031025 ) 14 by 19 pitch 3 bladed
aluminum Black Max style propeller. It actually measures 13 1/2 diameter
from being reconditioned and balanced by Johnny's Propeller Service in
Detroit Michigan.
Click here for picture of our #3171 thrust
washer which is required but not included.
$65.00
Click here for 10 pounds
shipping from our zip 48316
Change the zip to your zip for
shipping cost. |
Remanufactured GM Delco Marine Starter
 This
starter was rebuilt by Marv's
Auto Electric in Utica Michigan. It mounts from the bottom of the
engine and is held in place with (1) long bolt & (1) short bolt and
has a straight across bolt pattern. It was used on many older
in-line 4 & 6 cylinder and V-8 GM engines. This will not fit a Ford.
$95.00 |
MerCruiser
- Reconditioned 21 Pitch Prop
 This
is a reconditioned MerCruiser ( p/n # 48-78122-21 ) 13 3/4 by 21 pitch 3
bladed aluminum Black Max style propeller. It actually measures 13 1/4
diameter from being reconditioned and balanced by Johnny's Propeller
Service in Detroit Michigan.
Click here for picture of our #3171 thrust
washer which is required but not included.
$65.00
Click here for 10 pounds
shipping from our zip 48316
Change the zip to your zip for
shipping cost. |
Used - Alpha Cooling Tool With Water Shut Off
 This
is a used 1965 - Date Pre-Alpha, Alpha One & Gen II cooling
tool which bolts to the bell housing when the outdrive is off. You can
attach your garden hose to this tool and run your engine all day long.
$30.00 Shipping
Wt. 1 1/2 Lbs.
|
Trim
Cylinder Test Fixture
This
is a test fixture we built years ago to check trim cylinders we rebuilt
for internal and external leaks. It uses a large garage door spring
to apply resistance against the trim cylinder as the pump extends and
retracts the piston. It will hold all MerCruiser trim cylinders. The pump
will develop and hold 3000 Lbs. of up pressure and 700 Lbs. of down
pressure. A long heavy duty cord with alligator clips is used to connect
to any 12 volt battery for power.
Click here
for a side view
$ 425.00
|
|
